Publicly routable IPv6 addresses behind CGNAT in home environment using Tailscale and VPS
from hempster@lemm.ee to selfhosted@lemmy.world on 04 Oct 2024 19:01
https://lemm.ee/post/44041747
from hempster@lemm.ee to selfhosted@lemmy.world on 04 Oct 2024 19:01
https://lemm.ee/post/44041747
I’ve set up subnet routing via Tailscale from my Oracle VPS to my home RPi4. The VPS has a static IPv4 and a /64 IPv6 allocation. I use the VPS to reverse traffic apps on the raspberry using nginx. I would like to take one step forward by tunneling v6 traffic from my home network to WAN, so every client gets its own IPv6 address. What’s the best way to tunnel IPv6 traffic from my home network through the RPi4 to the Oracle VPS? I’m also comfortable with messing up my Asus AC86U router to provide publicly routable IPv6 addresses to all clients via DHCP.
threaded - newest
You need to set up a publicly accessible device (in this case the VPS) as your IPv6 gateway
So you set up your VPN connecting your network to the VPS (should probably be set up from the router) and set your router to advertise an IP adress for the VPS which is routable from your local network as the gateway address (and should probably also run DHCPv6 for your network)
(note, I have not set up this stuff myself so I can’t help with implementation details)
How do I make the VPS as a gateway device? I see that I can do a static route, but IPv6 gateway is something im unable to understand
What they suggest sounds like setting up a bridge interface between your LAN and the VPN interface to connect the VPS with your LAN. That’s actually a good idea since it would not need you to have a separate /64 for your local network. In this case I’m pretty sure that your VPN needs to be a layer 2 VPN, i.e. transports whole ethernet frames instead of TCP/UDP only, for this to work correctly. Wireguard doesn’t do this, OpenVPN can for example.
To make the VPS a gateway, you need to configure it to forward packets between networks and then set it as your default route on the clients (with IPv6, default route is usually published using router advertisements, set up radvd service on your VPS for that). That’s pretty much it IIRC except for the firewall rules. Here’s an article that’s some cloud stuff but is also applicable to your situation: www.linode.com/…/linux-router-and-ip-forwarding/#…
I don’t think you can do this with routing because IPv6 doesn’t support splitting a /64 into subnets. Might work via virtual bridging over a vpn link. I don’t think tailscale supports layer 2 tunneling so you would need to use something else.
The easy way is to just use tunnelbroker.net, that is what I currently have (this would use one of their assigned net blocks, not the one from the VPS). Set it up on the Pi, set up IP forwarding with appropriate firewall rules, make the Pi serve RA so clients can assign themselves an IP, done (IIRC).
If you want to set up the v6/v4 gateway yourself, I would do this with a /64 you can fully route to your home network like you would get with tunnelbroker.net because then you don’t have to deal with the network split and essentially two gateways for the same network (your Pi and the VPS), because otherwise your clients would assume the VPS is directly reachable since it’s in the same network when in reality it would have to go through the gateway (you would have to set up an extra route in that case on every client, I think). You’d need a second network from Oracle for this.
But it’s pretty much the same thing I would assume plus the setup on the VPS side, make the VPN route your /64 block (or use 6in4 which is what tunnelbroker.net uses), configure IP forwarding on the Pi and the VPS between the VPN interface and local/WAN respectively.
Tunnelbroker doesn’t work behind CGNAT
Hm, it doesn’t? I’m not behind CGNAT but I’m in a network I don’t control (university dorm) so my gateway is just another device in the local network and I don’t have a public IP which I control, which I feel like should effectively be the same thing as CGNAT, and it works for me. Maybe it isn’t the same.
Not sure how’s that even possible, HE usually probes your IPv4 address before assigning a GUA
I had the network before moving here (created it when I did have a public IPv4). Can’t test creating one new since it will only allow me to make one per IP.